-550x550.png "LiteVNA 67 Vector Network Analyser 50 kHz–6.3 GHz, 7-inch")
-550x550h.jpg "LiteVNA 67 Vector Network Analyser 50 kHz–6.3 GHz, 7-inch")
%20(2)-550x550w.jpg "LiteVNA 67 Vector Network Analyser 50 kHz–6.3 GHz, 7-inch")
-80x80.png "LiteVNA 67 Vector Network Analyser 50 kHz–6.3 GHz, 7-inch")
-80x80h.jpg "LiteVNA 67 Vector Network Analyser 50 kHz–6.3 GHz, 7-inch")
%20(2)-80x80w.jpg "LiteVNA 67 Vector Network Analyser 50 kHz–6.3 GHz, 7-inch")
- Stock: In Stock
- Product code: Product cr6293
Accurate S‑parameters up to 6.3 GHz in the field
- Wide 50 kHz–6.3 GHz range for antennas, filters, cables and RF paths.
- Large 7" touchscreen — easy to read traces, work with markers and the Smith chart.
- Two rugged N‑Type ports with a reliable thread for frequent connections in the workshop and on-site.
- Standalone operation via a 7800 mAh battery plus a built-in stand for desktop use.
- Save results to microSD: slot + preinstalled 32 GB card for quick data transfer.
Description
LiteVNA 67 is a portable vector network analyser designed for practical RF/microwave measurements from 50 kHz to 6.3 GHz. The instrument generates a controlled test signal and measures amplitude and phase after interaction with the connected device, giving you a complete frequency response of a specific object — an antenna, coaxial cable, filter, attenuator or matching network. Unlike a spectrum analyser, LiteVNA works with a connected load and displays S‑parameters rather than the “over-the-air” spectrum.
For antenna tuning, it’s convenient to monitor S11: VSWR, return loss, impedance and resonances — all shown in LOGMAG/PHASE and on the Smith chart. For two-port tasks, S21 (PORT1→PORT2) is available to assess insertion loss, passband, out-of-band rejection and phase response. The specified S21 dynamic range is over 100 dB in the 50 kHz–3 GHz band and over 80 dB at 3–6.3 GHz, making the model suitable for amateur, service and lab scenarios.
The 7-inch capacitive touchscreen makes it comfortable to work with multiple traces and markers, quickly find the minimum VSWR, a filter’s bandwidth or a resonance point. The top-mounted ports do not block the display, and the fold-out stand holds the instrument at a convenient angle. Data is stored on microSD (32 GB already installed), while PC connection, firmware updates and charging are handled via USB‑C. Everything needed for a proper start is included: low-loss RG142‑PUR cables and OPEN/SHORT/LOAD calibration standards — calibrate at the connection plane to “remove” the influence of cables and adapters and obtain accurate results.
Specifications
- Type: portable vector network analyser (VNA)
- Operating frequency range: 50 kHz – 6.3 GHz
- Ports: 2× N‑Type
- Parameters/modes: S11, S21, LOGMAG, PHASE, SMITH, markers/traces
- S21 dynamic range (specified): >100 dB (50 kHz–3 GHz), >80 dB (3–6.3 GHz)
- Display: 7" capacitive touchscreen
- Storage: microSD, 32 GB card (installed)
- Interface: USB‑C (data/updates/charging)
- Battery: 7800 mAh
- Design: built-in stand, hardware control (wheel) on the side panel
- Port limits (marked on the case): up to +10 dBm RF, up to 10 V DC
Package contents
- LiteVNA 67 vector network analyser (model ZN-706) — 1 pc.
- microSD memory card 32 GB (installed) — 1 pc.
- RG142‑PUR RF cable 50 cm, N Male–N Male — 2 pcs.
- N‑Type Male calibration kit: OPEN / SHORT / LOAD — 1 set
- N Female–N Female adapter — 1 pc.
- USB‑A–USB‑C cable — 1 pc.
- Capacitive stylus — 1 pc.
- Protective case — 1 pc.
Cable features: RG142‑PUR RF Test Cable, N Male–N Male connectors, 50 cm length each, flexible PUR jacket; the two-cable set lets you perform two-port S21 measurements straight away.
